mirror of
https://github.com/espressif/esp-nimble.git
synced 2026-09-10 03:00:03 +00:00
Andrzej Kaczmarek
d73572eb4a
This patch removes current logging from LL/PHY (which is temporary only anyway) and replaces it by sysview tracing. This allows to see traces together with ISRs and tasks activity.
78 lines
3.0 KiB
YAML
78 lines
3.0 KiB
YAML
# Licensed to the Apache Software Foundation (ASF) under one
|
|
# or more contributor license agreements. See the NOTICE file
|
|
# distributed with this work for additional information
|
|
# regarding copyright ownership. The ASF licenses this file
|
|
# to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance
|
|
# with the License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing,
|
|
# software distributed under the License is distributed on an
|
|
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
|
|
# KIND, either express or implied. See the License for the
|
|
# specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
|
|
# Package: hw/drivers/nimble/nrf52
|
|
|
|
syscfg.defs:
|
|
BLE_PHY_SYSVIEW:
|
|
description: >
|
|
Enable SystemView tracing module for radio driver.
|
|
value: 0
|
|
|
|
BLE_PHY_CODED_RX_IFS_EXTRA_MARGIN:
|
|
description: >
|
|
This defines additional margin for T_IFS tolerance while in
|
|
RX on coded phy to allow maintaining connections with some
|
|
controllers that exceed proper T_IFS (150 usecs) by more
|
|
than allowed 2 usecs.
|
|
This value shall be only used for debugging purposes. It is
|
|
strongly recommended to keep this settings at default value
|
|
to ensure compliance with specification.
|
|
value: 0
|
|
BLE_PHY_DBG_TIME_TXRXEN_READY_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state when radio is enabled using PPI channels
|
|
20 or 21 and back to low state on radio EVENTS_READY.
|
|
This can be used to measure radio ram-up time.
|
|
value: -1
|
|
|
|
BLE_PHY_DBG_TIME_ADDRESS_END_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state on radio EVENTS_ADDRESS and back to low state
|
|
on radio EVENTS_END.
|
|
This can be used to measure radio pipeline delays.
|
|
value: -1
|
|
|
|
BLE_PHY_DBG_TIME_WFR_PIN:
|
|
description: >
|
|
When set to proper GPIO pin number, this pin will be set
|
|
to high state on radio EVENTS_RXREADY and back to low
|
|
state when wfr timer expires.
|
|
This can be used to check if wfr is calculated properly.
|
|
value: -1
|
|
|
|
BLE_PHY_NRF52840_ERRATA_164:
|
|
description: >
|
|
Enable workaround for anomaly 164 found in nRF52840.
|
|
"[164] RADIO: Low selectivity in long range mode"
|
|
This shall be only enabled for:
|
|
- nRF52840 Engineering A
|
|
value: 0
|
|
|
|
BLE_PHY_NRF52840_ERRATA_191:
|
|
description: >
|
|
Enable workaround for anomaly 191 found in nRF52840.
|
|
"[191] RADIO: High packet error rate in BLE Long Range mode"
|
|
This shall be only enabled for:
|
|
- nRF52840 Engineering B
|
|
- nRF52840 Engineering C
|
|
- nRF52840 Rev 1 (final silicon)
|
|
value: 1
|